Jump to content


Photo
* * * * * 1 votes

Need help with JPM error codes


  • Please log in to reply
8 replies to this topic

#1 bigslope

bigslope

    Junior Member

  • New Members
  • 29 posts

Posted 27 April 2005 - 08:01 PM

Hi all.

I really need help with a Jpm gold rush dual stake club machine. When i switch it on all it displays is "Error 29" and will not progress any further. It works perfect before but has been lying for a while not switched on.

Thanks all

#2 Guest_DAD_*

Guest_DAD_*
  • Guests

Posted 27 April 2005 - 08:23 PM

These were posted on Fruit Forums ages ago by Bugs Bunny. I've always found them useful.

OLD ERROR LOG INFO - As used on Casino Las-Vegas, Big 50 etc

ERROR & EVENT CODES

CODE FAULT CAUSES (IN ORDER OF PROBABILITY)
1.1 £1 COIN INPUT }
1.2 50P COIN INPUT }
1.3 20P COIN INPUT }
1.4 10P COIN INPUT } Coin jam, Coin mech, Mother board.
1.5 20P TOK. INPUT }
1.6 5P COIN INPUT }
1.8 COIN MECH. ERROR More than one line high, Coin mech
1.9 STRIM ALARM Coin mech strim detected, Mother board.

2.1 / 2.8 REEL 1 - REEL 8 Opto tab missing/faulty, Mother board.
2.9 REEL DISCONNECTED Reel disconnected,Loom O/C, Mother board.

4.1* REFILL Refill keyswitch made.
4.2* RESET On board reset switch operated.
4.3* BUTTON Button stuck on power up.
4.4 DIRECT INPUT % Key missing, Mother board.
4.5 B/DOOR OPEN Back door open
4.7 C/DOOR OPEN Cash door open

* = Event code only. N.B. In the case of *4.3 the machine will on power up show the code and illuminate the stuck button for a short period of time before continuing to run in the normal manner.

5.1 RAM RESET Program or Processor Board
5.3 FRAUD (OFF/ON Alarm) Machine turned off/on during play (with full play credit).
5.5 MODE OF PLAY Mode of play key, Mother board.
5.7 COIN VERIFICATION Verification Opto (Hopper or Payslide)
5.9 COIN DETECT ERROR Hopper drive PCB, Motherboard.

6.1 METER 1 Cash in meter, Mother board.
6.2 METER 2 Cash out meter, Mother board.
6.3 METER 3 Token in meter, Mother board.
6.4 METER 4 Token out meter, Mother board.
6.5 METER 5 Refill meter, Mother board.

7.1 E.D.C TIMEOUT E.D.C. not fitted E.D.C. faulty, Mother board.
7.2 - 7.9 E.D.C Errors E.D.C. faulty, Mother board.

In the case of a protocol failure the code 7.1 will always be shown at the time of failure.

8.1 CHECKSUM FAIL Machine program changed.
8.2 RAM FAIL Processor board.
8.3 % CHANGE Change of aiming %. (new processor/program fitted)
8.4 MODE Mode of play changed.
8.5 RAM CORRUPTION Processsor board.
8.6 SOFTWARE RESET Program has performed a security reset.

9.0 / 9.1 SOFTWARE Processor board, program.
9.2 / 9.3 SOFTWARE/MPU Processor board, program.
9.4 SOFTWARE Program
9.6 WATCHDOG FAILURE Processor board

Any other code with a prefix of 9 indicates a fault on the mother or processr board, or software.
To assist in fault location the test routine must be entered to confirm if components (ie, lamps, level sensors, DIL switches etc) are electrically sound.
NEW ERROR LOG INFO




ERROR CODES
(Bacta 6 Standard Codes in Bold)


Code Sup Description
00 00 Unknown Error Occurred
01 00 Payout Verification Error
01 40 Non Payout 5p Cash
01 41 Non Payout 10p Cash
01 42 Non Payout 20p Cash
01 43 Non Payout 50p Cash
01 44 Non Payout 100p Cash
01 49 Non Payout 10p Token
01 4A Non Payout 20p Token
01 4B Non Payout 50p Token
01 4C Non Payout 100p Token

10 00 Payout Value Negative
10 01 20 Token Coin In Fault
10 02 ME129 More than 1 line high
11 00 £1 coin in fault
12 00 50p coin in fault
13 00 20p coin in fault
14 00 10p coin in fault
15 00 20p Token coin in fault
16 00 Note Acceptor Fault
19 00 Strim Error

20 00 General Reel Error
20 01 Reel 7 Opto Check Error
20 02 Reel 8 Opto Check Error
20 05 Reel Loom Reel Error
21 00 Reel 1 Opto Check Error
22 00 Reel 2 Opto Check Error
23 00 Reel 3 Opto Check Error
24 00 Reel 4 Opto Check Error

25 00 Reel 5 Opto Check Error
26 00 Reel 6 Opto Check Error
30 00 General Lamp Failure

40 00 General Operational Errors
40 01 Back Door Open
40 02 Back Door Closed
40 03 Cash Door Open
40 04 Cash Door Closed
40 05 Test Routine Activated
41 00 Refill Mode Entered
42 00 Memory Cleared
43 00 Button Stuck
44 00 No % key
46 00 Call Attendant
47 00 Refill Required
45 00 Payaim change occurred
48 00 On/Off Tamper Alarm
49 00 No Stakes / Prizes Keys


Code Sup Description
50 00 General Electronic Problems
51 00 EPROM Failure
52 00 PAL Error
53 00 Ram Check Fail
54 00 Hardware Error
55 00 Sparking Detected
56 00 PSU Fail

60 00 General Meter Fault
60 01 Meter Detect Fail, 7
60 02 Meter Detect Fail, 8
61 00 Meter 1 -(Cash In) Fault
62 00 Meter 2 -(Cash Out) Fault
63 00 Meter 3 -(Token In) Fault
64 00 Meter 4 -(Token Out) Fault
65 00 Meter 5 -(Refill) Fault
66 00 Meter 6 -(Prizes Out) Fault

70 00 General Dataport Error
70 07 BBX Lock Up
70 08 BBX Buffer Full
70 01 Data Carrier Lost Error
70 02 Framing Error Detected
70 03 Over Run Error
70 04 Parity error
70 05 Blackbox NAK/other rec’d
70 06 Blackbox Called And Active
71 00 Waiting for Dataport
72 00 Faulty Comms Link

88 00 Program Change

90 -9f Manufacturer Software Alarms
90 00 Attempt To Divide By Zero
90 01 Hundred Hertz List Full
90 02 Processor Bus Error
90 03 Address Alignment Error
90 04 Illegal Instruction
90 05 Autovector 6 Watchdog

91 00 Illegal Mode
91 01 Control Pointer Omitted

92 00 Mainboard Access Violation (S.A)
92 01 Credit Gone Negative
92 02 Hopper Fraud, Pulses seen

93 00 Data Logger Failed
93 01 Writing To Data Logger

94 00 Vend Out Not Seen, 1
94 01 Vend Out Not Seen, 2
94 02 Vend Out Not Seen, 3
94 03 Vend Out Not Seen, 4
94 05 Vend Tamper, 1
94 06 Vend Tamper, 2
94 07 Vend Tamper, 3
94 08 Vend Tamper, 4


DAD

#3 bigslope

bigslope

    Junior Member

  • New Members
  • 29 posts

Posted 27 April 2005 - 09:19 PM

Thanks for the very quick reply. Hopefully this will help solve the problem. I will look at the machine tomorrow and report back.

#4 mocochoco

mocochoco

    Senior Member

  • Regulars
  • 1380 posts

Posted 27 April 2005 - 09:26 PM

cheers for that, it'l come in handy ;)

#5 richy76

richy76

    Member

  • New Members
  • PipPip
  • 403 posts

Posted 21 February 2008 - 02:34 PM

There is a casino crazy club on ebay says it has error code N9.
Does anyone know what this means as i am thinking of having a bid.
Thanks.

#6 impact

impact

    Error 9.4

  • Regulars
  • 1280 posts

Posted 21 February 2008 - 05:58 PM

if impact mk1/2 processor card or impact. if mk3 impact n9 code all my years of doing impact i have never came across n9 error
.._-=It`s not a problem only a challenge =-_..

#7 richy76

richy76

    Member

  • New Members
  • PipPip
  • 403 posts

Posted 21 February 2008 - 06:16 PM

I havent heard of it either, he says its not working now & before it had a starting bid of £9.99 & now it £59.99 or £60 buy it now & he said it no longer powers up.
I am not going to bother now as he doesnt know what he is talking about by the sound of it.

#8 bill4676

bill4676

    Junior Member

  • New Members
  • 15 posts

Posted 21 September 2009 - 10:32 AM

6.1 METER 1 Cash in meter only getting it when i put money in them machin restarts it self

#9 dcole22

dcole22

    Newbie

  • New Members
  • 3 posts

Posted 19 April 2019 - 09:24 AM

I know this is an old post but Im getting error 85 11 on my JPM Rameses Riches machine. Has anybody come across it before?




0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users