Jump to content


Photo
* * * * * 1 votes

Fruit Machines Inside Out: Manufacturing


  • Please log in to reply
10 replies to this topic

#1 edwardb

edwardb

    Junior Member

  • Regulars
  • 223 posts

Posted 10 July 2018 - 03:46 PM

Hi All

 

I thought I'd write some info about the manufacturing process of AWP machines. Obviously, this differed by manufacturer but you might find it interesting to know how machines were made, how some companies different in production methods and some of the cock ups that were made.

 

Cabinets

------------

 

Carcass cabinets used to be made in-house at most companies until the late 1990s/early 2000s. Barcrest, Maygay and Bell Fruit all had "cab shops" where CNC routers would cut cabinet parts from sheets of MDF or chipboard, which were then bolted together to make the bare carcass. Later, companies such as Cabinet Developments ("cabdev") or Postern Cabinet Co started to take over as running a cab shop was a cost that could be done without.

Cabinets and all the tooling that goes into making them is VERY expensive (in the hundreds of thousands), and so changes to cabinets designs were not frequent. Modifications to payout systems to combat fraud were fairly common, and some necessitate a change in cabinet design to amend coin routing, to stop rodding etc.
 

A fun fact is that BFM used to use their CNC routers overnight to make kitchen cabinets for MFI back in the 90s. Might as well earn some money from your machinery when it's not needed.

 

Wiring & Vac Forms

---------------------------

All the big companies made the majority of wiring harnesses in-house until the late 90s. Barcrest and Bell Fruit used to hand-wire lampboards (the plastic vacuum formed panels behind the glass) using a machine that would illuminate a sequence of lamps, and the operators would follow with a wire and insertion tool, and then crimp the wire, put it in the plug and do the next lamp row/column.

 

For complex games with lots of multicoloured lamps this was a pain, and a laborious process, so it eventually got outsourced too.

 

It wasn't uncommon to have mistakes where pins on a plug were misplaced, and so the wrong lamps lit, and you would have to go through and figure out which ones were wrong and change them over.

 

MPUs/PCBs

-----------------

 

With the exception of Barcrest (until MPU5 days) all companies outsourced MPU manufacture. I think Maygay might have done some in house but PCB pick & place machines are very expensive. Far easier to get someone else to do it.

 

A fun fact is that Heber, based near Stroud (Glos) who made MPUs used in many of the smaller & foreign manufacturer's machines, also designed custom hardware for some of the bigger manufacturers. They did a video board for Barcrest. They also make shower and washing machine controllers. Good bunch of guys, always like seeing them.

 

Reels & Buttons

---------------------

 

Reels and buttons were almost exclusively supplied by Gamesman and Starpoint. They would arrive in large boxes, and someone would have the fun job of fitting reel strips and inserting button decals. 

Barcrest (I think) used to make their own reel assemblies in the MPU4 days, before moving to off the shelf reels.

 

Glass

-------

 

I started when screen printing was dying off. The artists would send a file (over an ISDN line, or often a CD sent via post!) to the print company who would produce a test batch of 5 glasses, normally. It wasn't uncommon to see them being "off register" - that is, with one of the 4 colours (CMYK) being slightly off and the art looking smudged as a result. 

 

One of the funniest things I saw was the Hi Lo reel aperture being filled with a solid red - should be clear/transparent - which resulted in all glasses being scrapped. Bang goes a few hundred quid.

 

BFM used to print their own glasses in-house, but they stopped in the mid 90s as digital printing took off. No more 4 colour seps, just a large format inkjet printer, which printed to a film which was then stuck to the glass. A black backing was added to stop light bleeding out.

 

Glasses arrives on pallets and were built up into the finished doors, complete with gas struts and lampboard, ready to be hung on the cabinet.

 

 

Production

--------------

 

Barcrest and Maygay had their "flow line" - akin to a car factory, where a carcass cabinet was put on the line at one end, and operatives would fit parts as it rolled down the line, leaving a finished machine at the end. This was efficient, they could manage 2k/3k machines a month with ease.

 

Bell Fruit used to make everything on "stills" - literally a box on which the machine sat, and then one person would build up an entire machine. Not as efficient but often better quality.

 

During busy periods it was not uncommon to have the factory working 24/7 on three shifts, and sods law you would have a hit machine in the UK at the same time as you had a hit machine in say Holland or Germany, resulting in a high demand for machines. UK normally got priority.

 

Conversely lean periods meant people sat around doing nothing, so a lot of factory staff were temps, which meant that quality could be hit and miss until they were trained up properly.

 

Final Inspection

---------------------

 

At Mazooma, we took delivery of machines to our offices in Newark, where we would inspect each machine and correct faults. I will never forget my first big seller, Sinbad 2000 for Germany, where we had an initial small production run of 300 machines, arranged in two long rows the length of the warehouse, all with their front door open - like a guard of honour. As an 18/19 year old that was pretty cool to see.

 

We would install the software, and then power up each machine in turn (or 8 at a time if you were good!) and just check it fired up. Reel faults and cable snags were common. We checked they spun to the correct position and we would set the real-time clock. You would then run a few coins through it, ensuring the hopper and coin mech worked, and checked the mechanical meters were OK, before doing a RAM reset, switching it off and bagging it up for trucking to site.

 

Machines were loaded on a wagon and off to wherever.

 

Though I was a developer I always liked getting my hands dirty in whatever needed doing - every day was a school day and it set you apart from those who wouldn't get their hands dirty.

 

I think I've covered everything but as always, feel free to ask any questions!

 

 


  • Johnnyafc , thecodfather , Mavroz and 6 others like this

#2 stanmarsh14

stanmarsh14

    Sado-masochist

  • Gold Supporters
  • 3120 posts

Posted 10 July 2018 - 04:13 PM

Fact about Maygay when they was on the MMM system..... this was made by a firm called Pannelwire Controls LTD, in Heanor, Derbyshire..... same place was also involved in some of the control circuits that went in to the Sinclair C5.

Also Maygay, like Electrocoin used Poterson (Near Cardiff I believe), for some of their cab building.



#3 vectra666

vectra666

    No1. Lurker

  • Layout Creator
  • PipPipPipPipPip
  • 9040 posts

Donator

Posted 10 July 2018 - 05:52 PM

Nice to read my near home town being mentioned great read
The more I do today, The less I do tomorrow.
Fme is alive and screaming into the 21st century!
Enjoy FME and Happy Gaming!!!!

#4 ricardo de ponsa

ricardo de ponsa

    Man Of Science

  • Regulars
  • 1110 posts

Posted 10 July 2018 - 07:45 PM

Thanks Edwardb for a very very interesting post with a personal insight on the production process of gaming machines.


Don't come round and steal my Cheerios !!!!


#5 nails

nails

    The furniture

  • Regulars
  • 4578 posts

Posted 10 July 2018 - 09:43 PM

good bit of info there.

 

i was gutted when Barcrest stopped making reel based machines. 

 

Look at the dire state of the machines left out there now!



#6 edwardb

edwardb

    Junior Member

  • Regulars
  • 223 posts

Posted 11 July 2018 - 12:36 PM

Fact about Maygay when they was on the MMM system..... this was made by a firm called Pannelwire Controls LTD, in Heanor, Derbyshire..... same place was also involved in some of the control circuits that went in to the Sinclair C5.

Also Maygay, like Electrocoin used Poterson (Near Cardiff I believe), for some of their cab building.

 

Panelwire, blimey that's a blast from the past. Yes they did a lot of AWP stuff, and also a lot of automotive too IIRC.



#7 Mavroz

Mavroz

    odd job man...

  • Layout Creator
  • PipPipPip
  • 882 posts

Posted 11 July 2018 - 02:18 PM

Who / which company (ies)  used to print the reelbands and decals for machines?

 

Who still does?

 

Thanks.



#8 iamtheone

iamtheone

    Junior Member

  • Regulars
  • 30 posts

Posted 12 July 2018 - 10:55 PM

http://www.shadesgra...ment-gaming.htm

They still print those sorts of things.
  • Mavroz likes this

#9 Mavroz

Mavroz

    odd job man...

  • Layout Creator
  • PipPipPip
  • 882 posts

Posted 13 July 2018 - 08:39 AM

Thank you.

#10 Twostroker

Twostroker

    Newbie

  • New Members
  • 129 posts

Posted 14 July 2018 - 08:34 PM

Great post... great read.

#11 edwardb

edwardb

    Junior Member

  • Regulars
  • 223 posts

Posted 17 July 2018 - 10:04 AM

Yeah I think Shades are still around, and Wave Design in South Wales. I used to use Wave to print art for my own export games when I was freelance. Good bunch of guys.


  • Mavroz likes this




0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users